← Knowledge base
IPANDA / KNOWLEDGE BASE / COMPARISON

Water repellent comparison for stone and paving

These six products serve different purposes. Choose your material and desired finish first, then estimate working-solution volume from the number of coats and a test application.

Water repellent comparison for stone and paving
ProductSurfaceFormAppearanceHow to calculate useHow it worksCompatibility limitations
PROSEPT AQUAISOL ↗Source and instructions ↗Absorbent stone, concrete, mineral plaster, paving1:2 concentrate · 5 L makes 15 L of working solutionPreserves the original look after drying; no designed wet-stone effect0.3–0.5 L/m² working solution total for two passes
Area × rate; concentrate = working solution ÷ 3
A water-based silane-siloxane system that reduces water absorption in mineral substrates.Check substrate absorbency and moisture. Polished stone and previously treated surfaces require a separate test.
ТИПРОМ К ↗Source and instructions ↗Porous brick, concrete, stone and plaster1:3 concentrate · 5 L makes 20 L of working solutionPreserves appearance, with no visible film0.15–0.30 L/m² working solution to saturation
Area × rate; concentrate = working solution ÷ 4
A penetrating organosilicon concentrate that imparts water-repellent properties.Protect glass, metal, plastic and plants. Follow the storage and application conditions in the technical data sheet.
ТИПРОМ У ↗Source and instructions ↗Stone, brick, concrete, paving and facadesReady to use · 5 LKeeps the natural appearance, with no visible filmSAZI catalogue: 1 L per 3.5–5 m²; about 0.20–0.286 L/m²
Area × measured ready-to-use consumption
A ready-to-use, solvent-based organosilicon formulation that makes pores water-repellent.Not intended for gypsum; not recommended for certain limestones. Dense clinker with water entering from behind requires a separate assessment. Test before use.
ТИПРОМ М ↗Source and instructions ↗Stone, brick, concrete, paving; check timber suitability separatelyReady to use · 5 LDeepens colour with a wet-stone effectSAZI catalogue: 1 L per 3.5–5 m²; about 0.20–0.286 L/m²
Area × measured ready-to-use consumption
A water-repellent impregnating treatment with a colour-modifying effect.A test application is essential: the resulting shade depends on the original colour and porosity. Check compatibility with existing coatings.
ELCON AQWELL ↗Source and instructions ↗Natural and artificial stone, brick and concrete; confirm porosity requirements and suitability against the technical data sheet for the batchReady-to-use impregnating treatment · 9 L; do not diluteEnhances the natural colour; verify the result with a test applicationTechnical data sheet: 1 L per 6–8 m² per coat
Area × number of coats ÷ 6–8 m² per litre; add application losses
A penetrating formulation based on silanes and siloxanes in an organic solvent.Colour enhancement is not guaranteed to last in areas subject to constant abrasion or prolonged exposure to water. The manufacturer’s recommendations on porosity differ: check the technical data sheet for the specific batch and carry out a test.
ELCON WESTON ↗Source and instructions ↗Natural and engineered stone, granite, pavingReady-to-use stone varnish · 9 LDeepens colour with a pronounced wet-stone effect1 L per 6–7 m² PER coat; at least two coats
Area × number of coats ÷ 6–7 m² per litre
A protective and decorative stone varnish with a water-repellent effect.Check substrate dryness, adhesion and compatibility with the previous coating. Assess slipperiness after treatment in pedestrian areas.
01 / METHOD

How to find the actual rate

Clean and dry a representative test area. Account for porosity, application method and coat count. Measure the working solution used over a known area. For concentrates, convert the measured solution into product volume using the dilution ratio.

Universal calculator →
02 / EXAMPLE

Example for 20 m²

  • AQUAISOL: 6–10 L working solution for two passes → 2–3.33 L concentrate at 1:2.
  • ТИПРОМ К: 3–6 L working solution → 0.75–1.5 L concentrate at 1:3.
  • WESTON: two coats theoretically need 20 × 2 ÷ 7 ≈ 5.7 L to 20 × 2 ÷ 6 ≈ 6.7 L, before application losses.

The WESTON product-page headline “9 L = 50–60 m²” is close to one-coat coverage. The instructions call for at least two coats at 1 L per 6–7 m² per coat. Plan purchases from the coat count and a test patch, rather than the headline.

Marble, limestone, polished granite, glazed clinker and previously treated substrates require a separate compatibility check. All rates are indicative. Test compatibility and appearance on a small area before treating the full surface, and follow the instructions for your specific batch.